Although the number of manual transmission — or “stick shift” — vehicles on the road has decreased dramatically in recent years, from 35 percent of all vehicles in 1985 to about 10 percent today according to recent media reports, they’re still the preference of millions of drivers in the U.S.Drivers of stick shifts report better car handling, increased fuel mileage and lower cost to maintain.But highly rated mechanics on Angie’s List say there are a few issues unique to manual transmission vehicles that drivers should look out for in order to keep their stick shift in good working order. The job of the clutch is to transfer power from the engine to the transmission. Just like when the clutch slips, trouble shifting gears is another sign the clutch may need to be replaced.According to industry experts, trouble shifting or staying in gear could be a sign that an internal or external transmission part is worn or damaged, or it could signal an electrical problem.“An internal problem in the transmission would require a rebuild or replacement,” Waeiss says.An auto expert who specializes in transmissions can diagnose the issue.Trouble getting into the correct gear can also indicate you’re using the wrong type of transmission fluid or there’s a bad gear. Craig Douglas, president of highly rated in Indianapolis, says just like an automatic transmission, manual transmission fluid needs to be replaced to keep the internal components operating correctly.He adds that manufacturers have direct specifications, but recommends a fluid change around 45,000 to 60,000 miles. The average cost is about $75 to $150, he says.“This helps mitigate hydraulic failures,” Douglas says. “Modern vehicles no longer use cables or linkage to engage and disengage the clutch like in the older vehicles.”Gunning says leaks are also a common manual transmission problem. Leaks occur to the clutch components, including the master and slave cylinder and the hydraulic lines.“Drivers should be aware of fluid levels during routine fluid level checks,” he says.
One of the best ways to keep your manual transmission system fresh is by operating it correctly, Douglas says.“This is probably the biggest cause of failures,” he says. “Drivers starting off in second or third gear because they are tired of shifting, or skipping gears because they don’t feel like going through all of the proper gears.”He adds it’s important not to abuse the clutch pedal.“At a red light, make sure your foot is completely off the clutch,” Davis says. “Keeping your foot on the pedal will wear it down.”. A manual clutch is much like a disk break that operates reverse with respect to the peddle. When you let go of the clutch it has small but powerful springs (usually 4 or 6 of them) that push a steel pressure plate together with the clutch plate.
Mr8 mr10 mr2 m86 hm282 gm fwd cars. Mr8 mr10 mr2 m86 hm282 transmission parts & rebuild kits. Chevy buick olds pontiac front wheel drive.
The clutch plate is much like a break pad, and just like a break pad wears down, so does the clutch plate. When the break pads are gone, you don't stop. When the clutch plate is gone, you don't go. See, I said they operated reverse. The big difference is the clutch is 100 times harder to get to. I hope this helps.
That last statement was quite correct. You shouldn't have the clutch pedal depressed at all while waiting at a red light, or any time that the car is stopped; doing so would cause unnecessary wear of the throw-out bearing.The proper way to do this would be to disengage the transmission before coming to a stop. This will have the added benefit of ensuring that the gear teeth have a good layer of oil on them when it's time to get moving again.
Leaving the clutch pedal depressed while stationary stops the gears from rotating and the oil will drip down off the gear teeth. Even though the extra wear would be miniscule, it'll add up over the life of the transmission. It all happened so fast I'm really worried about the cause and cost.my car is a 2003 mitsubishi spyder. I take very good care of it and usually just drive it to work and back. I'm 31 now and have always owner a standard car. I got to work like any other day and everything was fine. After my shift when I got into the care I noticed the clutch had about an 1 inch give ( meaning it had no resistance, I could move it with 1 finger.).
![M86 5sp Manual Transmission M86 5sp Manual Transmission](http://allworldautomotive.com/images/userphotos/35609_62002.jpg)
I was thinking of going to a shop the neXT day not knowing the urgency. The next day I took it to work and the give was greater. By the time my next shift ended.
24 hrs the clutch had like 3 inches give. It wouldn't have any pressure until it was very close to the bottom.what could it possibly be?I know it's not leaking because there are no stains on my drive way. I hardly made it home.
Now I'm afraid to take it to a shop because I feel like any minute it won't grab. What could possibly act so quickly.
The car is running completely fine. Idle is fine. It's not maKing any noises. Anyways any feed back would be greatly appreciated. Hi I need your insight regarding an 06 Honda Civic. It shifts well however when the 1st gear is engaged, a noise is audible like a fast paced (tactactac); may be metal to metal contact. When shifting to 2nd, it is less audible and less again in 3rd gear.
On the 4th and 5th, no noise. I am sure it is related to the transmission because when I put the lever on neutral, the noise described previously disappears and will start over if engaged in 1,2 or 3rd gear.I am sure something is on its way out but have no idea what.Thanks for assisting.